HARDWARE / DIY ITW ZipLine Alpha hard-00039 $0.75 These zipper pulls offer some nice benefits over traditional plastic end tabs. Since a fancy visco-elastic molded rubber-like material it will not absorb fluids. Tensile strength is around 40lbs so plenty enough to stand up to normal use, but will break away if snagged during heavy movement rather than resulting in a bad day. Different sliders will offer... View
HARDWARE / DIY ITW Web Dominator hard-00010 $1.25 These lil guys are great for any gear with 1" straps that need slack management. Traditionally duct tape is used as semi-permanent solution, but with Web Dominators you can get the holding power with dramatically better on/off speed and no sticky mess to boot. This way the slack can still exist to give sizing options, yet isn't dangling everywhere as a... View
Out-of-Stock HARDWARE / DIY ITW Waveloc Male hard-00020 $0.50 NOTE: Only the male piece is sold on this page. For those tired of their straps slipping through normal buckles on actions such as rucking with speed, the Wavelocs offer a nice strong hold on 1" webbing. These will interface with other ITW 1" female pieces such as repair buckles, surface mounts, and the QASM. Due to the tight fit, only a single strip of... View
HARDWARE / DIY ITW TriGlide 1.5inch itw-105-0150 $0.90 The Triglide Strap Adjuster is perfect in any strap or webbing application where variable length is required. It also works well in combination with other buckles as a means of securing loose webbing needs. 1.5inch in particular is common for webbing adjustment on waist belts for packs. 1 unit = 1 Tri-GlideITW Part Number: 105-0150-xxxx View
HARDWARE / DIY ITW Tri-Glide 1inch hard-00053 $0.45 The Triglide Strap Adjuster is perfect in any strap or webbing application where variable length is required. It also works well in combination with other buckles as a means of securing loose webbing needs. 1 unit = 1 Tri-GlideITW Part Number: 105-0100-xxxx View
HARDWARE / DIY ITW Tac-Toggle hard-00019 $0.65 A simple piece of hardware that can enhance the pull capability of cordage. 2 holes in the center allow 550 cord size cord to be wrapped or tied as desired. Can be grabbed in numerous ways, but excels when gripped between fingers in a fist. Size is a good balance of grip-ability while not being a large snag hazard.ITW Part Number 743-0200-XXXX View
Out-of-Stock HARDWARE / DIY ITW Tac-Link hard-00023 $4.00 These are great for non climbing carabiners. Rated at about 300lbs breaking strength, this is more than enough to secure a weapon, yet is a good spec to break away if heavily snagged to prevent injury. The latch hook has also been removed for general easier usability. The TAC-LINK is a high strength polymer attachment device with GhillieTEX™ IR signature... View
HARDWARE / DIY ITW SurfaceMount 1inch hard-00021 $1.00 ITW 1" Surface Mount Buckle consisting of 3 parts to make 1 unit:810-1059-xxxx – Surface Mount Buckle810-1060-xxxx – Surface Mount Base810-1058-xxxx – GTSR-1 maleAnother great SRB option, these Surface Mounts allow the female portion to be attached to fabrics. An example use is on magazine pouches as they enhance ease of use due to the female portion... View
HARDWARE / DIY ITW QASM hard-00018 $1.00 ITW 1" QASM (Quick Attach Surface Mount Buckle) consisting of 2 parts to make 1 unit:810-1076-xxxx – QASM Body810-1058-xxxx – GTSR-1 male(The result being 1 complete buckle)These are similar in concept to the repair buckles, however lay nice and flat consistently in place for a more low profile end result. Using the splits, no sewing is required and can... View
POUCHES / PANELS ITW Pistol FASTMag pouch-00008 $28.00 Based on the Original Fastmag design, this pistol variant offers the same great features to another caliber class. The open top design reduces reloading time for the operator and can be mounted in the up or down position. The enhanced urethane tension strap is adjustable to meet the users preference for removal tension. The FMP is also designed to... View
Out-of-Stock HARDWARE / DIY ITW Picatinny QASM Ramp hard-00050 $5.00 The Picatinny QASM-RAMP is designed to mount, hold and/or organize any/all of your M1913 Picatinny mountable accessories. Introduce this ultra-modular capability to your kit for unlimited mounting options in any location containing 1” sewn webbing. The new Picatinny QASM-RAMP can be used in numerous scenarios, whether it is mounting your incident camera,... View
Out-of-Stock HARDWARE / DIY ITW Mash Hook 1inch slot hard-00012 $3.00 The MASH (Metal All-purpose Snap Hook) gateless snap hook offers an alternative to the HK-style snap hooks in common use for sling systems. The MASH is constructed from stainless steel and comes in sizes for 1" and 1.25" wide webbing. (NOTE this page is selling the 1" slot version) Pressing on the thumb tabs in the middle separates the two rings,... View
Out-of-Stock HARDWARE / DIY ITW Mash Hook 1.25inch slot hard-00013 $3.25 The MASH (Metal All-purpose Snap Hook) gateless snap hook offers an alternative to the HK-style snap hooks in common use for sling systems. The MASH is constructed from stainless steel and comes in sizes for 1" and 1.25" wide webbing. (NOTE this page is selling the 1.25" slot version) Pressing on the thumb tabs in the middle separates the two rings,... View
Out-of-Stock FIELD SUPPLIES ITW Marine Whistle field-00002 $1.50 These whistles can serve military and civilians alike offering a way to get others' attention whether it be in a rescue or threat situation. The size is slim while still offering a nice grip with an incorporated clip that fits great on webbing. Usability is easy which is important in a stressful situation. Just blow hard and you will be good to go making... View
HARDWARE / DIY ITW Looploc 1inch itw-111-0100 $0.25 A simple hardware loop for various webbing interfacing such as adding connections or slack management. 1 unit = 1 LooplocITW Part Number: 111-0100-xxxx View
Out-of-Stock HARDWARE / DIY ITW GTSR Waveloc Split-Bar 1inch Male itw-810-1083 $1.00 NOTE: Only the male-latch piece is sold on this page. For those tired of their straps slipping through normal buckles on actions such as rucking with speed, the Wavelocs offer a nice strong hold on 1" webbing. These will interface with other ITW and Duraflex 1" female pieces such as repair buckles, surface mounts, and the QASM. Being different from the... View
Out-of-Stock HARDWARE / DIY ITW GTSR Waveloc Split-Bar 1inch Female itw-810-1082 $1.00 NOTE: Only the female-body piece is sold on this page. For those tired of their straps slipping through normal buckles on actions such as rucking with speed, the Wavelocs offer a nice strong hold on 1" webbing. These will interface with other ITW and Duraflex 1" male pieces. Being different from the original Waveloc this split-bar version allows for a... View
HARDWARE / DIY ITW GTSR SPLIT-BAR LATCH Male 1inch itw-810-1072 $1.00 A handy split-bar buckle part to allow more repair style buckle options. Great for replacing pack hardware and adding buckles to PALS webbing. These parts can interface with other 1" Duraflex Military buckle parts too. Note: This product is just for the male side and fixed slot / non adjustable style.ITW part number: 810-1072-xxxx View
Out-of-Stock HARDWARE / DIY ITW GTSR 1inch Waveloc Body hard-00078 $0.75 NOTE: Only the female / body piece is sold on this page. For those tired of their straps slipping through normal buckles on actions such as rucking with speed, the Wavelocs offer a nice strong hold on 1" webbing. These will interface with other ITW 1" male pieces. Due to the tight fit, only a single strip of webbing will fit through the slots so in some... View
HARDWARE / DIY ITW GTSP Cordlock hard-00011 $0.65 These cordlocks are designed with adventure use in mind. Top has raised bars for extra grip, side slots allow sew-down capability, and the bottom has a hole for drainage. The inside even has a raised wedge to enhance cord grip. The overall size is very compact allowing locking of 2 pieces of cord that are similar size to 550 paracord. These are great for... View
HARDWARE / DIY ITW GTLL 1inch Ladderloc hard-00077 $0.45 These are solid ladder-locks made with 1" webbing tactical product use in mind. Great for all kinds of quick adjustment applications; slings and backpack straps being a couple of examples. Typically attached on back slot, the front slot then offers one way webbing movement until tilted to offer two way webbing movement. With the lanyard hole one can add a... View
Out-of-Stock HARDWARE / DIY ITW GTLL 100 Split-Bar 1inch LadderLoc hard-00094 $0.65 Based on the original GTLL 100, but with a repair style slot for no-sew repairs. These are solid ladder-locks made with 1" webbing tactical product use in mind. Great for all kinds of quick adjustment applications; slings and backpack straps being a couple of examples. Typically attached on back slot, the front slot then offers one way webbing movement... View
Out-of-Stock HARDWARE / DIY ITW GT Waveloc XL 1inch Male itw-810-1081 $0.75 NOTE: Only the male piece is sold on this page. For those tired of their straps slipping through normal buckles on actions such as rucking with speed, the Wavelocs offer a nice strong hold on 1" webbing. These will interface with other ITW and Duraflex 1" female pieces such as repair buckles, surface mounts, and the QASM. Being different from the original... View
HARDWARE / DIY ITW GT Ruck 1inch Ladderloc itw-154-2100 $1.00 Hence the ruck part of the name, this is a beefed up version of a ladderlock to give the same functionality while holding up better to harder use. Hole on the pull tab allows for knotting cord for further pull options. 1 unit = 1 GT RuckITW Part Number: 154-2100-xxxx View