TACTICAL GEAR

1
…
19
20
21
…
24

ITW Tri-Glide 1inch

HARDWARE / DIY

ITW Tri-Glide 1inch

The Triglide Strap Adjuster is perfect in any strap or webbing application where variable length is required. It also works well in combination with other buckles as a means of securing loose webbing needs. 1 unit = 1 Tri-GlideITW Part Number: 105-0100-xxxx

View

HARDWARE / DIY

Adhesive Loop VELCRO® Brand

Sold by the foot, 1 unit = 1 foot. This is full on Military VELCRO® Brand Loop fuzzy side done with adhesive / sticky back - brand #72. Great for helmets, small electronics, weapon furniture, and more. The adhesive achieves full bond strength in 24 hours (after applying on the gear surface), and works well in temperature ranges from -20° F to 225° F.

View

HARDWARE / DIY

VELCRO® ONE-WRAP® Brand 1inch

Sold by the YARD:VELCRO® Brand ONE-WRAP® has many uses, but for gear it really shines offering strap and wire management. A great replacement to where duct-tape was the common choice in the past, with one-wrap being much easier to release and reuse. One side is hook and one is loop, however the hook style is done lower profile so it doesn't accidentally...

View

ITW Picatinny QASM Ramp

Out-of-Stock

HARDWARE / DIY

ITW Picatinny QASM Ramp

The Picatinny QASM-RAMP is designed to mount, hold and/or organize any/all of your M1913 Picatinny mountable accessories. Introduce this ultra-modular capability to your kit for unlimited mounting options in any location containing 1” sewn webbing. The new Picatinny QASM-RAMP can be used in numerous scenarios, whether it is mounting your incident camera,...

View

Fusion Terminal 8

Out-of-Stock

CLIMBING

Fusion Terminal 8

This aluminum descender has a large inside diameter with ears and belay slots. Large design makes it ideal for fast use in adverse conditions and easier to handle heavy loads. Ears allow user the ability to tie off the rope to use both hands freely. Overall approx 6.8" x 6.7" Width Height Major Weight Weight 6.8" 6.7" 45kn...

View

MSM Pear-S Carabiner

CLIMBING

MSM Pear-S Carabiner

MIL-SPEC MONKEY

With no luck getting a hold of carabiners in good colors we had to take matters into our own hands. These are great Pear / HMS shape S-Screwlock carabiners; Light weight aluminum sporting a classic pin nose for the most strength. The Pear shape offers a large gate opening and can be a belay device using a HMS knot. The screw lock is well knurled for a...

View

ITW ZipLine Alpha

HARDWARE / DIY

ITW ZipLine Alpha

These zipper pulls offer some nice benefits over traditional plastic end tabs. Since a fancy visco-elastic molded rubber-like material it will not absorb fluids. Tensile strength is around 40lbs so plenty enough to stand up to normal use, but will break away if snagged during heavy movement rather than resulting in a bad day. Different sliders will offer...

View

MSM Retracto-Plugs

HARDWARE / DIY

MSM Retracto-Plugs

MIL-SPEC MONKEY

Based on the tech used on our DLUX CG hats we are now bringing the same great functionality for helmets. Each pack contains 2 retractors each with a plug, with hook and loop sticky-back fastener circles. The plugs themselves are triple-flange style, 25 db rated, and are also replaceable using a screw mount. Although most users will use hook and loop for...

View

Safety Snap DA

CLIMBING

Safety Snap DA

Very similar to the Kong Tango with the improvement of a bottom guard to shield the rear safety from being jammed up from foreign objects. A lot like a caribiner with a great balance of speed and security. Gate will not open until the rear safety is engaged which occurs naturally when gripped. Approx 5.5" long x 2.75" wide.

View

MSM QR Belt Rig

Out-of-Stock

HARDWARE / DIY

MSM QR Belt Rig

MIL-SPEC MONKEY

A seemingly simple rig made to allow a quick release setup on belts. The G-hook supplies many features including tri-glide functionality, alternate PALS connection, and enhanced grip when threading through both the hook and slots. Which side the pull cord faces can be easily changed by disassembling and flipping over the G-hook. Elastic is included to...

View

Para V-ring

HARDWARE / DIY

Para V-ring

Commonly used on rigger's belts, this V-ring fits 1.75" webbing, or 1-23/32" if you want to get para-technical. Forged steel and rated as Strength: 4000 lb

View

Para Adjuster Bar

Out-of-Stock

HARDWARE / DIY

Para Adjuster Bar

Commonly used on rigger's belts, this adjuster bar fits 1.75" webbing, or 1-23/32" if you want to get para-technical. Forged steel and rated as Strength: 5000 lb

View

Showing 229-240 of 282 item(s)

1
…
19
20
21
…
24

TACTICAL GEAR