HARDWARE / DIY

Out-of-Stock

HARDWARE / DIY

Keyring 1inch ID 1.25inch OD

Some simple EDC kit, these are sturdy black keyrings. Approx 1.25" outside diameter, 1" inside diameter. A slightly beefy version of the size most expect a common keyring to be.

View

HARDWARE / DIY

Keyring 1.25inch ID 1.5inch OD

hard-00025

$0.80

Some simple EDC kit, these are beefy dark grey keyrings. Approx 1.5" outside diameter, 1.25" inside diameter.

View

Out-of-Stock

HARDWARE / DIY

ITW 1" Oval Slide

ITW NEXUS

hard-00024

$0.75

A simple, yet handy slide. Can be used as a tri-glide or get creative such as making it interface with other hardware to create modular attachment points. Since flat and has more length than width it can be inserted into hardware loops creating a secure snag.

View

Out-of-Stock

HARDWARE / DIY

ITW Tac-Link

ITW NEXUS

hard-00023

$4.00

These are great for non climbing carabiners. Rated at about 300lbs breaking strength, this is more than enough to secure a weapon, yet is a good spec to break away if heavily snagged to prevent injury. The latch hook has also been removed for general easier usability. The TAC-LINK is a high strength polymer attachment device with GhillieTEX™ IR signature...

View

Out-of-Stock

HARDWARE / DIY

ITW G-Hook Wave

ITW NEXUS

hard-00022

$2.50

NOTE: These are the middle bar with wave variant 19241-22-2188xG-hooks offer compact webbing mods connecting with a simple hook to 1" webbing and offering 1" slots to connect additional webbing. Example attachment points include the sides of tac-vests or up on shoulder straps (packs or vests). Since metal, the G-hooks are very flat compared to a typical...

View

HARDWARE / DIY

ITW SurfaceMount 1inch

ITW NEXUS

hard-00021

$1.00

ITW 1" Surface Mount Buckle consisting of 3 parts to make 1 unit:810-1059-xxxx – Surface Mount Buckle810-1060-xxxx – Surface Mount Base810-1058-xxxx – GTSR-1 maleAnother great SRB option, these Surface Mounts allow the female portion to be attached to fabrics. An example use is on magazine pouches as they enhance ease of use due to the female portion...

View

Out-of-Stock

HARDWARE / DIY

ITW Waveloc Male

ITW NEXUS

hard-00020

$0.50

NOTE: Only the male piece is sold on this page. For those tired of their straps slipping through normal buckles on actions such as rucking with speed, the Wavelocs offer a nice strong hold on 1" webbing. These will interface with other ITW 1" female pieces such as repair buckles, surface mounts, and the QASM. Due to the tight fit, only a single strip of...

View

HARDWARE / DIY

ITW Tac-Toggle

ITW NEXUS

hard-00019

$0.65

A simple piece of hardware that can enhance the pull capability of cordage. 2 holes in the center allow 550 cord size cord to be wrapped or tied as desired. Can be grabbed in numerous ways, but excels when gripped between fingers in a fist. Size is a good balance of grip-ability while not being a large snag hazard.ITW Part Number 743-0200-XXXX

View

HARDWARE / DIY

ITW QASM

ITW NEXUS

hard-00018

$1.00

ITW 1" QASM (Quick Attach Surface Mount Buckle) consisting of 2 parts to make 1 unit:810-1076-xxxx – QASM Body810-1058-xxxx – GTSR-1 male(The result being 1 complete buckle)These are similar in concept to the repair buckles, however lay nice and flat consistently in place for a more low profile end result. Using the splits, no sewing is required and can...

View

Product available with different options

HARDWARE / DIY

Multicam Loop VELCRO® Brand

Velcro

hard-00015

$2.00

This is full on VELCRO® Brand Loop fuzzy side done in Multicam camouflage with excellent color matching. Sold by the foot, 1 unit = 1 foot, this is the sew on version.

View

HARDWARE / DIY

Hook and Loop

hard-00014

$3.50

Good MIL-Spec stuff and we are selling it by the foot. Hook is the male side with little hooks while loop is the the soft female side. This is the sew on version. Both sides, hook and loop are supplied with each foot unit purchased.

View

Out-of-Stock

HARDWARE / DIY

ITW Mash Hook 1.25inch slot

ITW NEXUS

hard-00013

$3.25

The MASH (Metal All-purpose Snap Hook) gateless snap hook offers an alternative to the HK-style snap hooks in common use for sling systems. The MASH is constructed from stainless steel and comes in sizes for 1" and 1.25" wide webbing. (NOTE this page is selling the 1.25" slot version) Pressing on the thumb tabs in the middle separates the two rings,...

View

Out-of-Stock

HARDWARE / DIY

ITW Mash Hook 1inch slot

ITW NEXUS

hard-00012

$3.00

The MASH (Metal All-purpose Snap Hook) gateless snap hook offers an alternative to the HK-style snap hooks in common use for sling systems. The MASH is constructed from stainless steel and comes in sizes for 1" and 1.25" wide webbing. (NOTE this page is selling the 1" slot version) Pressing on the thumb tabs in the middle separates the two rings,...

View

HARDWARE / DIY

ITW GTSP Cordlock

ITW NEXUS

hard-00011

$0.65

These cordlocks are designed with adventure use in mind. Top has raised bars for extra grip, side slots allow sew-down capability, and the bottom has a hole for drainage. The inside even has a raised wedge to enhance cord grip. The overall size is very compact allowing locking of 2 pieces of cord that are similar size to 550 paracord. These are great for...

View

Out-of-Stock

HARDWARE / DIY

ITW Web Dominator

ITW NEXUS

hard-00010

$1.25

These lil guys are great for any gear with 1" straps that need slack management. Traditionally duct tape is used as semi-permanent solution, but with Web Dominators you can get the holding power with dramatically better on/off speed and no sticky mess to boot. This way the slack can still exist to give sizing options, yet isn't dangling everywhere as a...

View

HARDWARE / DIY

ITW 1" Repair Buckle

ITW NEXUS

hard-00009

$0.75

ITW 1" Repair Buckle (SRB) consisting of 2 parts to make 1 unit:810-1064-xxxx – SR 1” female replacement buckle810-1058-xxxx – GTSR-1 male The main design goal for these buckles was to replace broken 1" Side Release Buckles (SRB) without any sewing required. They work great for that, however I like to use them to add straps to my gear since they easily...

View

HARDWARE / DIY

ITW Grimloc

ITW NEXUS

hard-00008

$2.00

ITW Military Products Grimloc (Locking D-ring) ITW Part Number 110-4100-xxxx Originally made to allow Marines to add hydration carriers to their vests, these Grimlocs can be added to anything with PALS / MOLLE style 1" webbing. Once on, they make a great attachment point for weapon slings, lanyards, pouches, and more! The Grimloc™ is fabricated from...

View

Out-of-Stock

HARDWARE / DIY

Snap Shackle Mini

MIL-SPEC MONKEY

hard-00007

$7.50

Cool hardware for quick release applications, smaller than usual size. Spring loaded, latch will not release until ring is pulled sideways away from the shackle. Latch can be resecured without pulling ring. Come a little stiff, but break in well. Main shackle piece is approx 0.875" x 1.25"

View

Out-of-Stock

HARDWARE / DIY

Snap Shackle Large

MIL-SPEC MONKEY

hard-00006

$12.00

Some customers wanted a load bearing snap shackle, so here you go in cool guy black to boot. A little bit pricey, but cool hardware for quick release applications. Spring loaded, latch will not release until ring is pulled sideways away from the shackle. Latch can be resecured without pulling ring. 2.625" total length when closed x 1.5" width not counting...

View

Out-of-Stock

HARDWARE / DIY

Snap Shackle Medium

MIL-SPEC MONKEY

hard-00005

$9.50

A quick release snap shackle in a common 2" overall length size. Classic hole slot is easier to come by so a cheaper option than the 1" webbing slot version. Spring loaded, latch will not release until ring is pulled sideways away from the shackle. Latch can be resecured without pulling ring. Approx 1.25" x 1.875" closed and not counting the pull ring.

View

Out-of-Stock

HARDWARE / DIY

Snap Shackle 1" slot

MIL-SPEC MONKEY

hard-00004

$8.50

Black color with 1" slot. A little bit pricey, but cool hardware for quick release applications. Spring loaded, latch will not release until ring is pulled sideways away from the shackle. Latch can be resecured without pulling ring. Although not for human load bearing, it can still hold a lot of weight. Approx 1.25" x 1.625" closed and not counting the...

View

Out-of-Stock

HARDWARE / DIY

HK Snaphooks - ITW Clash-hooks

ITW NEXUS

hard-00003

$4.25

Clash Hooks, ITW Military's take on the HK style 1" slot Snap Hooks: offering cool guy colors and solid quality.ITW Part Number: 09267-23-210xx

View

Out-of-Stock

HARDWARE / DIY

Kong Frog

Kong

hard-00016

$22.00

These are a pretty cool unique high speed connector hardware piece. The size works great for climbing type rope or connecting to hardware such as D-rings on Rigger's Belts. To operate, just push the side tabs in and the front will be ready for insertion. Connecting will cause the system to auto close. To release, gently pull away while pushing in the side...

View

Showing 121-143 of 143 item(s)